Description
The FAAC 413 24V Double Kit provides a complete automation package for a double swing gate, combining two FAAC 413 24Vdc electromechanical operators with the FAAC E034 control board, compatible radio receiver and two remote transmitters.
Designed for residential double swing gate automation, the FAAC 413 24Vdc combines powerful linear operation with a low-voltage 24Vdc motor, integrated mechanical travel stops and continuous-duty capability.
The FAAC E034 control board manages both operators from a single control system, allowing the two gate leaves to operate together while providing programmable leaf delay, pedestrian opening, automatic closing, safety device management and other advanced automation functions.
📦 Complete FAAC 413 24V Double Gate Kit
This kit includes the primary automation and control components required for a double swing gate installation.
Included in the package:
- 2 x FAAC 413 24Vdc Swing Gate Operators
- 1 x FAAC E034 Control Board
- 1 x Compatible FAAC Receiver
- 2 x Compatible FAAC Transmitters
With two operators included, one FAAC 413 is installed on each gate leaf and both operators are controlled through the central E034 electronic control system.
Safety and access control accessories can be added separately according to the requirements of the installation.
⚙️ Twin FAAC 413 24Vdc Operators
The kit includes two FAAC 413 24Vdc non-reversing electromechanical linear operators, providing independent powered movement of each swing gate leaf.
Each operator uses a 24Vdc motor and worm-screw drive system to extend and retract the operator rod, converting linear movement into controlled movement of the gate leaf.
Each FAAC 413 24Vdc provides:
- 24Vdc motor
- 2500N maximum thrust
- 1700N rated thrust
- 300mm working travel
- Up to 350mm maximum travel without integrated mechanical stops
- 16mm/sec rod speed
- Continuous-duty operation at 20°C
- Integrated opening and closing mechanical stops
- Manual release system
- Non-reversing operation
- IP54 protection
💪 2500N Maximum Thrust Per Operator
Each FAAC 413 24Vdc operator develops up to 2500N of maximum thrust, with a rated thrust of 1700N.
With one operator installed on each gate leaf, both sides of the double swing gate are independently powered and controlled by the E034 control system.
The operators should not be selected based solely on their maximum thrust.
Each gate leaf must be correctly installed, aligned and capable of moving freely by hand before automation is fitted.
Gate construction and wind loading are particularly important considerations with solid or heavily clad double swing gates.
📏 Suitable for Gate Leaves up to 2.5 Metres Each
Each FAAC 413 24Vdc operator is designed for an individual swing gate leaf up to:
- 1.8m without an electric lock
- 2.5m with an appropriate electric lock
This means the kit can automate a pair of compatible gate leaves, with one operator controlling each leaf.
For gate leaves exceeding 1.8m, an appropriate electric lock should be fitted to securely hold the gates in the closed position.
Gate construction, weight, wind loading, hinge position and installation geometry must also be considered when determining operator suitability.
🛑 Integrated Mechanical Stops
Each FAAC 413 incorporates adjustable opening and closing mechanical travel stops.
These stops allow the travel of each operator to be mechanically established within the operator itself.
The standard working travel is approximately 300mm when the integrated mechanical stops are used.
Where the internal mechanical stops are not used, maximum available operator travel increases to approximately 350mm.
Because each leaf of a double gate has its own operator, the travel and mounting geometry of each side must be correctly established during installation.
⚡ 24Vdc Motor Technology
Each FAAC 413 uses a 24Vdc electric motor rated at 70W.
The low-voltage motor system allows the E034 electronic control board to precisely manage the operation of both gate leaves.
Benefits of the 24Vdc system include:
- Electronic motor control
- Independent control of two operators
- Adjustable operating force
- Smooth gate movement
- Opening and closing slowdown
- Electronic safety management
- High-frequency residential operation
- Compatibility with optional battery backup equipment
🧠 FAAC E034 Control Board Included
The kit includes the FAAC E034 electronic control board for managing both 24Vdc gate operators.
The E034 acts as the central control system for the double gate, coordinating the movement of both leaves while processing commands from the receiver, safety devices and other connected accessories.
Depending on programming and connected equipment, available functions can include:
- Double swing gate operation
- Independent control of two 24Vdc operators
- Automatic closing
- Semi-automatic operation
- Pedestrian opening
- Gate leaf delay
- Adjustable motor force
- Opening slowdown
- Closing slowdown
- Safety beam management
- Electric lock control
- Accessory inputs
- Radio receiver integration
- Programmable operating logic
- Optional battery backup capability
This allows the automation to be configured according to the requirements of the gate and property.
🚪 Programmable Gate Leaf Delay
Double swing gates commonly require one leaf to begin moving before the other.
This is particularly important where the gate leaves overlap in the closed position or where an electric lock arrangement requires a specific opening and closing sequence.
The E034 can coordinate the two operators so the gate leaves operate in the correct sequence.
The required leaf delay is configured during commissioning according to the physical arrangement of the gate.
🚶 Pedestrian Opening
The E034 control system can provide pedestrian opening using a single gate leaf.
Instead of opening both sides of the driveway gate, a pedestrian command can operate only the designated leaf.
This provides convenient pedestrian access without requiring the complete double gate to open.
It is particularly useful where the driveway gate also serves as the primary pedestrian entrance to the property.
📡 FAAC Receiver Included
The kit includes a compatible FAAC radio receiver.
The receiver connects to the E034 control system and receives coded commands from the compatible FAAC transmitters.
This allows the double gate to be conveniently operated remotely from a vehicle or other suitable location.
Additional compatible transmitters can be programmed where more users require access.
🎛️ Two FAAC Transmitters Included
Two compatible FAAC remote transmitters are supplied with the kit.
This provides remote gate operation for two users or vehicles immediately after the automation has been installed, programmed and commissioned.
Additional compatible transmitters can be added separately for:
- Additional vehicles
- Family members
- Employees
- Property managers
- Authorised visitors
- Spare remote controls
Depending on the receiver and programming configuration, different transmitter buttons can also be assigned to functions such as full gate opening and pedestrian access.
👁️ Safety Beam Compatible
Compatible FAAC Safety Beams can be connected to the E034 control system to provide additional obstruction detection around the automated gate.
Photoelectric Safety Beams create an infrared detection path across the protected area.
When a person, vehicle or other obstruction interrupts the beam, the control board can respond according to the programmed safety function.
Safety Beams can be positioned to protect areas such as:
- The driveway opening
- Closing gate movement
- Opening gate movement
- Vehicle access areas
- Areas between the gate leaves
- Potential trapping or crushing zones
The required safety system should be determined according to the individual gate installation.
🚌 FAAC BUS 2easy Technology
The E034 supports compatible FAAC BUS 2easy accessories.
BUS 2easy uses a two-wire communication system for compatible safety and control devices, helping simplify wiring where multiple accessories are installed.
Compatible BUS devices can include FAAC photocells and other automation accessories.
This can be particularly useful on double swing gate installations where multiple safety zones need to be monitored.
🔋 Battery Backup Compatible
The 24Vdc automation platform allows compatible emergency battery backup equipment to be added to the system.
When correctly configured, battery backup can allow the double gate automation to continue operating during a mains power failure.
This can be particularly useful where:
- The automated gate is the property’s primary vehicle entrance
- There is no alternative vehicle access
- Power failures are common
- Continued automated access is important during an outage
Battery backup equipment is not included in this kit unless separately specified.
🔄 Smooth Gate Movement
The E034 control system can manage operating force and slowdown to provide smooth movement of both gate leaves.
Controlled slowdown near the end of opening and closing travel reduces abrupt stopping forces on the gate and automation system.
This can help reduce unnecessary mechanical shock on:
- Gate hinges
- Operator mounting brackets
- Gate frames
- Gate posts
- Mechanical travel stops
Each operator must be correctly mounted and programmed for its respective gate leaf.
🔒 Non-Reversing Operation
The FAAC 413 uses a non-reversing electromechanical drive arrangement that mechanically resists movement of the gate when the operator is stationary.
For compatible gate leaves up to 1.8m, the operators can provide the required locking function without an additional electric lock under suitable installation conditions.
For gate leaves exceeding 1.8m and up to the maximum 2.5m application, an appropriate electric lock should be installed.
An electric lock can also be beneficial on double gates with overlapping leaves, gates exposed to significant wind loads or installations requiring additional closed-gate security.
🔑 Manual Release on Both Operators
Each FAAC 413 incorporates its own manual release system.
If the automation cannot operate because of a power failure, equipment fault or maintenance requirement, each operator can be manually released so its respective gate leaf can be moved by hand.
Both gate leaves should remain capable of smooth manual movement independently of the automation system.
🌧️ Designed for Outdoor Gate Automation
The FAAC 413 24Vdc is specifically designed for external swing gate automation.
Each operator features:
- IP54 protection
- Operating temperature from -20°C to +55°C
- Double-coated aluminium operator body
- Horizontal cable exit suitable for low mounting positions
Correct installation, sealing and cable management remain important for long-term reliability in outdoor environments.
🏡 Ideal for Double Residential Swing Gates
This kit has been specifically configured for automation of two swing gate leaves.
Typical applications include:
- Double residential driveway gates
- Aluminium swing gates
- Steel swing gates
- Open-style swing gates
- Custom fabricated driveway gates
- Existing manual gate upgrades
- New automated gate installations
- Higher-frequency residential entrances
One FAAC 413 operator is installed on each gate leaf, with both operators controlled by the E034.
📐 Installation Geometry Is Critical
Linear swing gate operators rely heavily on the relationship between the gate hinge, rear operator mounting point and front attachment position.
The maximum gate leaf dimensions alone do not guarantee that the FAAC 413 will fit a particular gate.
For both gate leaves, consideration must be given to:
- Gate hinge position
- Gate post dimensions
- Required opening angle
- Rear bracket position
- Front attachment position
- Gate leaf construction
- Available operator clearance
- Operator stroke
- Mechanical travel requirements
Each side of a double gate should be assessed individually, as hinge and post geometry can vary between the two leaves.
🏗️ Gate Construction & Wind Loading
The maximum gate leaf length should not be considered independently of the gate’s construction.
Solid or heavily clad double swing gates can create substantial wind loading, placing significantly greater forces on the operators, hinges and mounting points than open-style gates of the same dimensions.
Operator selection should therefore consider:
- Individual gate leaf length
- Individual gate leaf weight
- Percentage of solid infill
- Wind exposure
- Hinge condition
- Gate frame rigidity
- Required opening angle
- Installation geometry
For large solid gates or unusually exposed installations, professional assessment is recommended before selecting the automation system.
⭐ Key Features
- Genuine FAAC double swing gate automation package
- 2 x FAAC 413 24Vdc operators
- 1 x FAAC E034 control board
- Compatible FAAC receiver included
- 2 x compatible FAAC transmitters included
- Designed specifically for double swing gates
- One powered operator per gate leaf
- 24Vdc electromechanical drive
- 2500N maximum thrust per operator
- 1700N rated thrust per operator
- 300mm working travel
- Up to 350mm maximum travel without internal stops
- 16mm/sec rod speed
- Continuous-duty operation at 20°C
- Integrated opening and closing mechanical stops
- Suitable for gate leaves up to 1.8m without electric lock
- Up to 2.5m per leaf with appropriate electric lock
- Programmable gate leaf delay
- Pedestrian opening using a single leaf
- Adjustable operating force
- Opening and closing slowdown
- Automatic closing capability
- Compatible with FAAC Safety Beams
- BUS 2easy accessory compatibility
- Optional battery backup capability
- Manual release on both operators
- IP54 operator protection
🔧 Specifications
- Manufacturer: FAAC
- Operator Model: 413 24Vdc
- Operator Quantity: 2
- Control Board: FAAC E034
- Operator Type: Linear Electromechanical Swing Gate Operator
- Application: Double Swing Gate
- Motor Voltage: 24Vdc
- Motor Power: 70W per operator
- Maximum Thrust: 2500N per operator
- Rated Thrust: 1700N per operator
- Rod Speed: 16mm/sec
- Working Travel: 300mm
- Maximum Travel Without Mechanical Stops: 350mm
- Maximum Leaf Width Without Electric Lock: 1.8m per leaf
- Maximum Leaf Width With Electric Lock: 2.5m per leaf
- Duty: Continuous at 20°C
- Operator Protection Rating: IP54
- Operating Temperature: -20°C to +55°C
- Manual Release: Yes, on both operators
- Integrated Opening Mechanical Stops: Yes
- Integrated Closing Mechanical Stops: Yes
- Gate Leaf Delay: Programmable
- Pedestrian Opening: Yes
- Safety Beam Compatibility: Yes
- Battery Backup: Optional
- Radio Receiver: Included
- Remote Transmitters: 2 Included
🔗 Compatibility
The FAAC 413 24V Double Kit is designed for compatible double swing gate installations.
Each FAAC 413 operator is suitable for an individual gate leaf up to 1.8m without an electric lock and up to 2.5m when an appropriate electric lock is installed.
Operator suitability depends on gate construction, individual leaf weight, hinge geometry, available mounting dimensions, wind exposure and other installation conditions.
Compatible FAAC Safety Beams, electric locks, battery backup systems, access controls and other automation accessories can be added separately where required.
⚠️ Please Note
This kit includes:
- 2 x FAAC 413 24Vdc Swing Gate Operators
- 1 x FAAC E034 Control Board
- 1 x Compatible FAAC Receiver
- 2 x Compatible FAAC Transmitters
This is a double swing gate kit and includes one operator for each gate leaf.
Safety Beams, electric locks, battery backup, flashing lights and other safety or access control accessories are not included unless separately specified.
For individual gate leaves exceeding 1.8m and up to the 2.5m maximum, an appropriate electric lock should be installed.
Gate dimensions are only one factor in operator selection. Gate weight, construction, wind loading, hinge position and installation geometry must also be considered.
For safety and correct operation, the automation should be installed and commissioned in accordance with FAAC installation instructions and applicable Australian requirements.
