Description
The ATA Axess Pro Logic Console C01L V2 is an advanced wall-mounted control and programming interface designed for compatible ATA Axess Pro industrial roller shutter operators and the ATA GDO-10 Toro commercial roller door operator.
Unlike the simpler C03M Manual Console, the C01L V2 provides a comprehensive LCD-based control system with programmable operating parameters, integrated TrioCode™128 remote control receiver, multiple safety inputs, external control inputs and advanced automatic door functions.
The console allows the operator to be programmed, controlled and diagnosed from ground level, providing a central interface for sophisticated commercial and industrial roller shutter installations.
📟 LCD Logic Control Interface
The C01L V2 incorporates an LCD display with a menu-driven programming system.
The display provides direct access to the Axess Pro operator’s settings and allows installers to view and adjust operating parameters without accessing the motor assembly.
The interface incorporates dedicated controls for:
- Open
- Stop
- Close
- Set
- Previous
- Next
These controls are used both for normal door operation and for navigating the programming menus.
🔧 Ground-Level Programming
One of the major advantages of the Logic Console is the ability to configure the industrial door operator from a conveniently accessible wall-mounted position.
Rather than repeatedly accessing an operator installed several metres above floor level, important settings can be viewed and adjusted directly through the console.
This makes commissioning, servicing and future adjustments significantly more convenient, particularly on large commercial and industrial roller shutters.
⚙️ Advanced Operator Configuration
The C01L V2 provides access to a wide range of Axess Pro operating parameters.
Through the LCD menu system, authorised installers can navigate through the available settings and adjust the behaviour of the operator to suit the individual door.
Parameters can be viewed, edited and saved directly through the console, with the Open and Close controls used to adjust selected values.
This provides substantially greater configuration capability than a basic Open / Stop / Close wall station.
📡 Built-In TrioCode™128 Receiver
The C01L V2 incorporates ATA’s TrioCode™128 remote control receiver directly into the Logic Console.
This allows compatible ATA remote controls to be programmed directly into the industrial door system without requiring a separate external receiver.
The multi-frequency radio system provides secure wireless access while being designed to provide reliable operation in environments where radio interference may be present.
👥 Up to 511 Remote Controls
The integrated receiver provides substantial transmitter memory capacity for commercial and industrial applications.
Up to 511 four-button transmitter codes can be stored within the system.
This makes the C01L V2 particularly suitable for applications requiring remote access for multiple users, including:
- Commercial premises
- Industrial facilities
- Warehouses
- Staff parking areas
- Shared commercial buildings
- Storage facilities
- Fleet vehicle access
- Multi-user sites
Remote controls can be managed through the Logic Console, providing a centralised approach to wireless access control.
👁️ Multiple Safety Beam Inputs
The V2 Logic Console provides dedicated connections for up to three safety beam inputs.
The terminal arrangement includes:
- SB1 – Safety Beam 1
- SB2 – Safety Beam 2
- SB3 – Safety Beam 3
- Accessory supply
- Common safety beam connections
This provides considerable flexibility when configuring safety equipment around a large commercial or industrial door opening.
Multiple safety devices can be particularly useful where additional protection is required around vehicles, pedestrians or other areas surrounding the roller shutter.
🔥 Dedicated Fire Input
The C01L V2 provides a dedicated FIRE input for integration with compatible external systems.
The Fire input can be configured for Normally Open or Normally Closed operation, allowing the industrial door system to interact with appropriate fire or building-control equipment where required.
The exact operation and configuration must be determined according to the requirements of the individual installation and associated building systems.
🔌 External Control Inputs
The C01L V2 provides a comprehensive terminal block for connection of external controls and accessories.
Available inputs include:
- Open
- Stop
- Close
- General Purpose Input
- Fire Input
- Safety Beam 1
- Safety Beam 2
- Safety Beam 3
Open, Stop and Fire inputs provide configurable Normally Open or Normally Closed operation, while additional connections allow external controls to be integrated into the complete automation system.
This makes the Logic Console particularly useful for customised industrial access-control installations.
🔗 Access Control Integration
The external control inputs allow the Axess Pro system to interact with other access-control equipment.
Depending on the requirements of the site, compatible equipment can be connected to provide operating commands to the industrial door.
This makes the C01L V2 suitable for integration into applications such as:
- Commercial access-control systems
- Key switches
- Push-button stations
- Intercom systems
- Building management systems
- Vehicle access systems
- External automation controls
The required interface and configuration depend on the equipment being connected.
🔄 Programmable Inputs & Outputs
The C01L V2 provides greater flexibility than a conventional fixed-function garage door controller.
Selected inputs can be configured according to the requirements of the installation, while the auxiliary output provides a connection point for compatible external equipment.
This allows the control system to be adapted to more complex commercial applications rather than limiting the installation to a basic standalone roller shutter.
⏰ Real-Time Clock & Scheduling
The Logic Console incorporates real-time clock functionality, allowing time-based operating functions to be incorporated into compatible Axess Pro installations.
This can be particularly useful for commercial premises where access requirements change throughout the day or week.
Potential applications include:
- Business-hour access
- Staff access periods
- Delivery windows
- Restricted after-hours operation
- Scheduled automatic functions
- Commercial access management
The C01L V2 provides 24-hour / 7-day programmable timer functionality for compatible operating functions.
🔄 Automatic Closing Functions
When appropriately configured with the required safety equipment, the Logic Console allows automatic closing functionality to be incorporated into the industrial door system.
This can be particularly useful in warehouses and commercial facilities where roller shutters may otherwise be accidentally left open.
Automatic closing can assist with:
- Building security
- Access control
- Weather protection
- Temperature control
- Operational efficiency
Appropriate safety devices must be installed and correctly configured when unattended or automatic door movement is enabled.
🚶 Partial / Pedestrian Opening
The Axess Pro control system can provide a programmable partial opening position.
Rather than opening the complete roller shutter every time access is required, the door can be moved to an intermediate position.
This can be useful where:
- Pedestrian access is required
- Ventilation is required
- Full vehicle clearance is unnecessary
- Reducing unnecessary door travel is desirable
The required partial opening position can be programmed according to the individual installation.
🛑 Advanced Safety Control
The C01L V2 forms an important part of the Axess Pro safety and control system.
By combining operator monitoring with dedicated safety inputs and configurable operating parameters, the console allows the industrial door system to be commissioned around the requirements of the individual site.
Appropriate safety devices should always be selected according to the size of the door, operating mode, surrounding environment and intended use.
🧠 Door Profiling & Obstruction Control
With a compatible Axess Pro operator, the Logic Console provides access to the operator’s door profiling and obstruction-related settings.
The system can monitor the normal operating characteristics of the roller shutter and use this information as part of its safety control.
This is particularly valuable on large industrial doors where the load experienced by the operator can vary throughout the door’s travel.
🩺 Diagnostics & System Information
The LCD interface also provides an important diagnostic function.
System information, operating status and relevant fault information can be viewed from the Logic Console, helping technicians identify problems without immediately needing to access the industrial operator.
This can make servicing considerably more efficient, particularly where the motor is installed high above the floor.
🔧 Easier Servicing & Maintenance
Industrial roller shutter operators are commonly mounted several metres above ground level.
By placing the primary programming interface at ground level, the C01L V2 reduces the amount of operator access required for routine programming and diagnostics.
This makes it easier to:
- Check system status
- Adjust operating parameters
- Program remote controls
- Review settings
- Configure accessories
- Diagnose operating problems
The console therefore provides benefits not only during initial installation but throughout the service life of the operator.
🔌 RJ45 Connection
The C01L V2 communicates with the compatible operator through its dedicated data connection.
ATA documentation identifies an RJ45 connection on the console for communication with the operator.
This allows the wall-mounted console to act as the primary user and programming interface for the complete industrial door automation system.
🏭 Designed for Industrial Applications
The C01L V2 is specifically designed around the requirements of commercial and industrial door automation.
Typical applications include:
- Industrial roller shutters
- Warehouse doors
- Factory entrances
- Workshop roller shutters
- Commercial garage doors
- Storage facilities
- Commercial vehicle entrances
- High-use industrial access points
Its combination of local control, programmable logic, remote receiver and external inputs makes it considerably more capable than a conventional garage door wall control.
🆚 Logic Console vs Manual Console
ATA provides both Manual and Logic Console options for compatible Axess Pro operators.
The C03M Manual Console is primarily intended for straightforward locally supervised operation where advanced automatic functions are not required.
The C01L V2 Logic Console provides a much more comprehensive control solution, adding features such as:
- LCD programming
- Integrated TrioCode™128 receiver
- Remote control management
- Multiple safety beam inputs
- External control inputs
- Programmable operating parameters
- Automatic operating functions
- Time-based functionality
- Advanced diagnostics
For installations requiring sophisticated automatic operation or remote-controlled access, the C01L V2 is generally the more appropriate control solution.
🔗 Axess Pro & Toro Compatibility
The C01L V2 is designed for use with compatible ATA industrial and commercial door operators.
Known compatible applications include:
- ATA Axess Pro 3110
- ATA Axess Pro 3310
- ATA Axess Pro 3315
- ATA GDO-10 Toro
Current listings also identify the C01L V2 under ATA Part No. 14856.
🔧 Genuine ATA Control Console
The C01L V2 is a genuine Automatic Technology Australia control component designed specifically for compatible ATA commercial and industrial door operators.
Using the correct ATA Logic Console ensures compatibility with the operator’s communication system, programming functions, safety inputs and remote control technology.
For an Axess Pro installation requiring advanced automatic functionality, the C01L V2 provides the primary interface between the operator, installer, user and connected accessories.
Key Features
- Genuine ATA Axess Pro Logic Console
- Model C01L V2
- ATA Part No. 14856
- Wall-mounted industrial control interface
- LCD display
- Menu-driven programming
- Ground-level operator configuration
- Dedicated Open control
- Dedicated Stop control
- Dedicated Close control
- Previous / Next menu navigation
- Set programming control
- Built-in TrioCode™128 receiver
- Stores up to 511 four-button transmitter codes
- Multi-frequency remote control technology
- Three dedicated safety beam inputs
- Dedicated Fire input
- General Purpose Input
- External Open input
- External Stop input
- External Close input
- Auxiliary output
- Accessory power supply
- Configurable N/O and N/C inputs
- Real-time clock functionality
- 24/7 programmable timer capability
- Automatic closing capability
- Partial opening functionality
- Advanced operator programming
- Diagnostic information through LCD display
- RJ45 communication connection
- Designed for commercial and industrial applications
Specifications
- Manufacturer: Automatic Technology Australia (ATA)
- Product: Axess Pro Logic Console
- Model: C01L V2
- ATA Part Number: 14856
- Product Type: Industrial Door Logic Control Console
- Installation: Wall Mounted
- Display: LCD
- Programming Interface: Menu Driven
- Controls: Open / Stop / Close / Set / Previous / Next
- Radio Receiver: Integrated TrioCode™128
- Transmitter Capacity: Up to 511 Four-Button Transmitter Codes
- Safety Beam Inputs: 3
- Fire Input: Yes
- General Purpose Input: Yes
- External Open Input: Yes
- External Stop Input: Yes
- External Close Input: Yes
- Auxiliary Output: Yes
- Accessory Supply: Yes
- Configurable Input Polarity: N/O & N/C on Supported Inputs
- Real-Time Clock: Yes
- Programmable Timer: 24-Hour / 7-Day
- Connection to Operator: RJ45 / Data Connection
- Application: Commercial & Industrial Door Automation
ATA’s current Axess Pro documentation confirms that the V2 Logic Console provides three safety-beam inputs, accessory supply, Fire, GPI, Open, Stop and Close inputs, an auxiliary output, LCD display and RJ45 connection.
Compatibility
The ATA C01L V2 Logic Console is suitable for compatible ATA commercial and industrial operators, including:
- ATA Axess Pro 3110
- ATA Axess Pro 3310
- ATA Axess Pro 3315
- ATA GDO-10 Toro
Compatibility listings specifically identify the C01L V2 with the Axess Pro 3110, 3310 and 3315, while the same C01L V2 / Part No. 14856 is also listed for the GDO-10V3 Toro.
⚠️ Please Note
The C01L V2 is an advanced Logic Console and should not be confused with the simpler C03M Manual Console.
Available functions depend on the operator, accessories, safety devices and configuration of the complete installation.
Automatic closing, remote operation and other unattended operating functions must only be configured with the appropriate safety equipment installed.
Installation, programming and commissioning should be carried out by an appropriately experienced industrial door technician.
