FAAC 413 24V Single Kit

Description

The FAAC 413 24V Single Kit provides a complete automation package for a single swing gate, combining the FAAC 413 24Vdc electromechanical operator with the FAAC E034 control board, compatible radio receiver and two remote transmitters.

Designed for residential swing gate automation, the FAAC 413 24Vdc combines powerful linear operation with a low-voltage 24Vdc motor, integrated mechanical travel stops and continuous-duty capability.

Paired with the advanced FAAC E034 control board, this kit provides sophisticated electronic control, safety management and programmable gate functions in a convenient single-gate automation package.

📦 Complete FAAC 413 24V Single Gate Kit

This kit includes the primary automation and control components required for a single swing gate installation.

Included in the package:

• 1 x FAAC 413 24Vdc Swing Gate Operator
• 1 x FAAC E034 Control Board
• 1 x Compatible FAAC Receiver
• 2 x Compatible FAAC Transmitters

The package provides a convenient starting point for automating a compatible single swing driveway gate, with safety and access control accessories able to be added separately according to the requirements of the installation.

⚙️ FAAC 413 24Vdc Electromechanical Operator

The FAAC 413 is a non-reversing electromechanical linear swing gate operator designed to provide powerful and controlled movement of residential swing gates.

The operator uses a 24Vdc motor and worm-screw drive system to extend and retract the operator rod, converting linear movement into movement of the swing gate leaf.

The FAAC 413 24Vdc provides:

• 24Vdc motor
• 2500N maximum thrust
• 1700N rated thrust
• 300mm working travel
• Up to 350mm maximum travel without integrated mechanical stops
• 16mm/sec rod speed
• Continuous-duty operation at 20°C
• Integrated opening and closing mechanical stops
• Manual release system
• Non-reversing operation
• IP54 protection

💪 Powerful 2500N Maximum Thrust

The FAAC 413 24Vdc develops up to 2500N of maximum thrust, with a rated thrust of 1700N.

This provides strong and reliable movement for compatible residential swing gates while the E034 electronic control board manages the operation of the motor and associated safety equipment.

The gate must still be correctly installed, aligned and capable of moving freely by hand before automation is fitted.

Gate leaf length alone should not be used to determine operator suitability, particularly where solid or clad gates are exposed to substantial wind loading.

📏 Suitable for Gate Leaves up to 2.5 Metres

The FAAC 413 24Vdc is designed for swing gate leaves up to:

• 1.8m without an electric lock
• 2.5m with an appropriate electric lock

For gate leaves exceeding 1.8m, an appropriate electric lock should be fitted to securely hold the gate in the closed position.

Gate construction, weight, wind loading, hinge position and installation geometry must also be considered when determining operator suitability.

🛑 Integrated Mechanical Stops

One of the useful features of the FAAC 413 is its integrated opening and closing mechanical travel stops.

These adjustable stops allow the operator’s travel to be mechanically limited within the operator itself.

The standard working travel is approximately 300mm when the integrated mechanical stops are used.

Where the internal mechanical stops are not used, maximum available operator travel increases to approximately 350mm.

Correct mounting geometry remains essential regardless of the travel configuration selected.

⚡ 24Vdc Motor Technology

The FAAC 413 uses a 24Vdc electric motor rated at 70W.

The low-voltage motor system allows the E034 electronic control board to precisely manage gate movement and provides a platform for advanced safety and automation functionality.

Benefits of the 24Vdc system include:

• Electronic motor control
• Adjustable operating force
• Smooth gate movement
• Opening and closing slowdown
• Electronic safety management
• High-frequency residential operation
• Compatibility with optional battery backup equipment

🧠 FAAC E034 Control Board Included

The kit includes the FAAC E034 electronic control board for managing the 24Vdc gate operator.

The E034 provides the central control system for the automation, processing commands from the receiver, safety devices and other connected accessories while controlling the movement of the gate operator.

Depending on system programming and connected accessories, functions can include:

• Single swing gate operation
• Automatic closing
• Semi-automatic operation
• Pedestrian opening
• Adjustable motor force
• Opening slowdown
• Closing slowdown
• Safety beam management
• Electric lock control
• Accessory inputs
• Radio receiver integration
• Programmable operating logic
• Optional battery backup capability

This provides considerable flexibility when configuring the automation to suit the property.

🚶 Pedestrian Opening

The E034 control system can provide pedestrian opening functionality.

Rather than operating the gate through its complete programmed opening cycle, a pedestrian command can partially open the gate to provide convenient pedestrian access.

This is particularly useful where the driveway gate is also regularly used as the property’s pedestrian entrance.

The required functionality depends on the system configuration and programming.

📡 FAAC Receiver Included

The kit includes a compatible FAAC radio receiver.

The receiver connects to the E034 control system and receives coded commands from the compatible FAAC transmitters.

This allows the gate to be conveniently operated remotely from a vehicle or other suitable location.

Additional compatible transmitters can be programmed where more users require access.

🎛️ Two FAAC Transmitters Included

Two compatible FAAC remote transmitters are supplied with the kit.

This provides remote gate operation for two users or vehicles immediately after the automation has been installed, programmed and commissioned.

Additional compatible transmitters can be added separately for:

• Additional vehicles
• Family members
• Employees
• Property managers
• Authorised visitors
• Spare remote controls

Depending on the receiver and programming configuration, different transmitter buttons may also be assigned to different automation functions.

👁️ Safety Beam Compatible

Compatible FAAC Safety Beams can be connected to the E034 control system to provide additional obstruction detection around the automated gate.

Photoelectric Safety Beams create an infrared detection path across the protected area.

When a person, vehicle or other obstruction interrupts the beam, the control board can respond according to the programmed safety function.

Safety Beams can provide protection for areas such as:

• The driveway opening
• Closing gate movement
• Opening gate movement
• Vehicle access areas
• Potential trapping or crushing zones

The required safety devices should be determined according to the individual gate installation and applicable safety requirements.

🚌 FAAC BUS 2easy Technology

The E034 supports compatible FAAC BUS 2easy accessories.

BUS 2easy provides a two-wire communication system for compatible safety and control devices, helping simplify installation where multiple accessories are required.

Compatible BUS devices can include FAAC photocells and other automation accessories.

The system allows compatible devices to communicate directly with the electronic control board while reducing the amount of conventional accessory wiring required.

🔋 Battery Backup Compatible

The 24Vdc automation platform allows compatible emergency battery backup equipment to be added to the system.

When correctly configured, battery backup can allow the gate automation to continue operating during a mains power failure.

This can be particularly useful where:

• The automated gate is the property’s primary vehicle entrance
• There is no alternative vehicle access
• Power failures are common
• Continued automated access is important during an outage

Battery backup equipment is not included in this kit unless separately specified.

🔄 Smooth Gate Movement

The E034 control system can manage acceleration, operating force and slowdown to provide smooth gate movement.

Controlled slowdown near the end of opening and closing travel reduces abrupt stopping forces on the automation and gate structure.

This can help reduce unnecessary mechanical shock on:

• Gate hinges
• Operator mounting brackets
• Gate frame
• Gate posts
• Mechanical travel stops

Correct programming and installation are essential for smooth and reliable operation.

🔒 Non-Reversing Operation

The FAAC 413 uses a non-reversing electromechanical drive arrangement that mechanically resists movement of the gate when the operator is stationary.

For compatible gate leaves up to 1.8m, the operator can provide the required locking function without an additional electric lock under suitable installation conditions.

For leaves exceeding 1.8m and up to the maximum 2.5m application, an appropriate electric lock should be installed.

An electric lock can also be beneficial where additional closed-gate security is required or where the gate is exposed to substantial wind loading.

🔑 Manual Release System

The FAAC 413 incorporates a secure manual release system.

If the automation cannot operate because of a power failure, equipment fault or maintenance requirement, the operator can be manually released so the gate leaf can be moved by hand.

Once automatic operation is available again, the operator can be re-engaged.

The gate must remain capable of smooth manual movement independently of the automation system.

🌧️ Designed for Outdoor Gate Automation

The FAAC 413 24Vdc is specifically designed for external swing gate automation.

The operator features:

• IP54 protection
• Operating temperature from -20°C to +55°C
• Double-coated aluminium operator body
• Horizontal cable exit suitable for low mounting positions

Correct installation and cable management remain important for long-term reliability in outdoor environments.

🏡 Ideal for Single Residential Swing Gates

This kit has been specifically configured for automation of one compatible swing gate leaf.

Typical applications include:

• Single residential driveway gates
• Single pedestrian gates
• Aluminium swing gates
• Steel swing gates
• Open-style swing gates
• Custom fabricated swing gates
• Existing manual gate upgrades
• New automated gate installations

For a conventional double swing gate with two powered leaves, two operators and an appropriately configured automation package are required.

📐 Installation Geometry Is Critical

Linear swing gate operators rely heavily on the relationship between the gate hinge, rear operator mounting point and front attachment position.

The maximum gate leaf dimensions alone do not guarantee that the FAAC 413 will fit a particular gate.

Before installation, consideration must be given to:

• Gate hinge position
• Gate post dimensions
• Required opening angle
• Rear bracket position
• Front attachment position
• Gate leaf construction
• Available operator clearance
• Operator stroke
• Mechanical travel requirements

The installation geometry specified for the FAAC 413 should be followed when determining the mounting positions.

🏗️ Gate Construction & Wind Loading

The maximum gate leaf length should not be considered independently of the gate’s construction.

A solid or heavily clad swing gate can experience substantial wind loading, potentially placing significantly greater forces on the operator, hinges and mounting points than an open-style gate of the same dimensions.

Operator selection should therefore consider:

• Gate leaf length
• Gate weight
• Percentage of solid infill
• Wind exposure
• Hinge condition
• Gate frame rigidity
• Required opening angle
• Installation geometry

For large solid gates or unusually exposed installations, professional assessment is recommended before selecting the automation system.

⭐ Key Features

• Genuine FAAC single swing gate automation package
• 1 x FAAC 413 24Vdc operator
• FAAC E034 control board included
• Compatible FAAC receiver included
• 2 x compatible FAAC transmitters included
• Designed for single swing gate automation
• 24Vdc electromechanical drive
• 2500N maximum thrust
• 1700N rated thrust
• 300mm working travel
• Up to 350mm maximum travel without internal stops
• 16mm/sec rod speed
• Continuous-duty operation at 20°C
• Integrated opening and closing mechanical stops
• Suitable for gate leaves up to 1.8m without electric lock
• Up to 2.5m with appropriate electric lock
• Adjustable operating force
• Opening and closing slowdown
• Pedestrian opening capability
• Automatic closing capability
• Compatible with FAAC Safety Beams
• BUS 2easy accessory compatibility
• Optional battery backup capability
• Manual release system
• IP54 operator protection

🔧 Specifications

• Manufacturer: FAAC
• Operator Model: 413 24Vdc
• Control Board: FAAC E034
• Operator Type: Linear Electromechanical Swing Gate Operator
• Application: Single Swing Gate
• Motor Voltage: 24Vdc
• Motor Power: 70W
• Maximum Thrust: 2500N
• Rated Thrust: 1700N
• Rod Speed: 16mm/sec
• Working Travel: 300mm
• Maximum Travel Without Mechanical Stops: 350mm
• Maximum Leaf Width Without Electric Lock: 1.8m
• Maximum Leaf Width With Electric Lock: 2.5m
• Duty: Continuous at 20°C
• Operator Protection Rating: IP54
• Operating Temperature: -20°C to +55°C
• Manual Release: Yes
• Integrated Opening Mechanical Stop: Yes
• Integrated Closing Mechanical Stop: Yes
• Safety Beam Compatibility: Yes
• Battery Backup: Optional
• Radio Receiver: Included
• Remote Transmitters: 2 Included
• Number of Operators: 1

🔗 Compatibility

The FAAC 413 24V Single Kit is designed for compatible single swing gate installations.

The operator is suitable for gate leaves up to 1.8m without an electric lock and up to 2.5m when an appropriate electric lock is installed.

Compatibility and operator suitability depend on gate construction, hinge geometry, available mounting dimensions, gate weight and environmental conditions.

Compatible FAAC Safety Beams, electric locks, access controls and other automation accessories can be added separately where required.

⚠️ Please Note

This kit includes:

• 1 x FAAC 413 24Vdc Swing Gate Operator
• 1 x FAAC E034 Control Board
• 1 x Compatible FAAC Receiver
• 2 x Compatible FAAC Transmitters

This is a single gate kit and includes one gate operator.

Safety Beams, electric locks, battery backup, flashing lights and other safety or access control accessories are not included unless separately specified.

For gate leaves exceeding 1.8m and up to the 2.5m maximum, an appropriate electric lock should be installed.

Gate dimensions are only one factor in operator selection. Gate weight, construction, wind loading, hinge position and installation geometry must also be considered.

For safety and correct operation, the automation should be installed and commissioned in accordance with FAAC installation instructions and applicable Australian requirements.