Description
The ATA Mounting Bracket Kit is a genuine mounting solution designed for the installation of compatible ATA Axess Pro 3000 Series industrial roller shutter operators.
The two-piece heavy-duty steel bracket assembly provides the structural mounting point required to securely position the Axess Pro operator alongside the roller shutter. The kit consists of an angle mounting plate and separate mounting angle, allowing the operator to be correctly positioned and aligned with the roller shutter drive system.
ATA lists the mounting bracket kit as a key accessory for the Axess Pro Series 3000 range.
🏗️ Heavy-Duty Operator Mounting
Industrial roller shutter operators generate substantial torque when opening and closing a door.
The Axess Pro Mounting Bracket Kit provides a strong structural mounting arrangement between the operator and the supporting building or roller shutter structure.
Correct mounting is essential to maintain:
- Operator alignment
- Drive chain alignment
- Structural rigidity
- Correct sprocket positioning
- Reliable power transmission
- Long-term operator performance
The supporting structure itself must also be capable of carrying the loads generated by the operator.
🔩 Two-Piece Bracket Design
The mounting kit consists of two primary steel components:
- 1 x Angle Mounting Plate
- 1 x Mounting Angle
The mounting plate incorporates a 92mm x 92mm hole pattern, while the separate angle measures approximately 50mm x 50mm x 265mm.
This two-piece arrangement provides a practical method of mounting the Axess Pro powerhead while allowing the installation to be configured around the individual roller shutter.
⚙️ Designed for Axess Pro Operators
The bracket kit is specifically designed for compatible ATA Axess Pro industrial roller shutter motors.
Rather than fabricating a generic mounting arrangement on site, the purpose-designed bracket provides a known mounting interface for the Axess Pro powerhead.
ATA’s Axess Pro Series 3000 documentation specifically identifies the Mounting Bracket Kit as an accessory for the range.
⛓️ Correct Chain Drive Alignment
Axess Pro industrial operators use a chain and sprocket arrangement to transfer power from the operator to the roller shutter.
Correct positioning of the motor is therefore important to maintain appropriate alignment between the operator output sprocket and the roller shutter drive sprocket.
The mounting bracket assists the installer in positioning the operator so the drive chain can be correctly aligned and tensioned.
Poor alignment can contribute to:
- Excessive chain wear
- Sprocket wear
- Increased operating noise
- Uneven loading
- Reduced drive efficiency
- Premature component failure
📐 92mm x 92mm Mounting Pattern
The angle mounting plate incorporates a 92mm x 92mm hole pattern designed around the Axess Pro mounting arrangement.
This provides the interface used to secure the compatible Axess Pro operator to the mounting assembly.
📏 265mm Mounting Angle
The second component of the kit is a heavy-duty angle measuring approximately:
- 50mm x 50mm
- 265mm long
This angle forms part of the structural mounting arrangement used to support and position the industrial operator.
🏭 Designed for Industrial Installations
The Mounting Bracket Kit is intended for the commercial and industrial environments in which Axess Pro operators are commonly installed.
Typical applications include:
- Industrial roller shutters
- Commercial roller shutters
- Warehouse doors
- Factory entrances
- Workshop roller shutters
- Storage facilities
- Commercial vehicle entrances
- Industrial access doors
The exact mounting arrangement will depend on the roller shutter construction and available supporting structure.
🔧 Suitable for New Installations
The bracket kit is ideal when installing a new Axess Pro operator onto a compatible industrial roller shutter.
It provides the installer with the primary operator mounting components required to position the motor alongside the roller shutter drive assembly.
The final installation must still account for the particular door, drive sprocket, chain alignment, available sideroom and supporting structure.
🔄 Ideal for Replacement Installations
The Mounting Bracket Kit can also be useful when replacing an existing industrial roller shutter operator with an ATA Axess Pro.
Where an older operator used a different mounting arrangement, the Axess Pro bracket provides the appropriate mounting interface for the replacement operator.
Additional fabrication or structural modifications may still be required depending on the existing installation.
💪 Secure Industrial Construction
A correctly installed mounting bracket is an important structural component of the complete industrial door automation system.
The bracket must withstand the reaction forces generated as the operator applies torque to the roller shutter.
For this reason, the bracket should be securely attached to an appropriate structural mounting point rather than lightweight cladding or other unsuitable building materials.
🧰 Genuine ATA Axess Pro Accessory
The Mounting Bracket Kit is designed specifically for the ATA Axess Pro range and provides a purpose-designed alternative to fabricating the complete motor mounting assembly on site.
ATA’s Series 3000 documentation identifies the kit with part number 92522.
Current replacement listings may also reference ATA SKU 62622, so the required part should be confirmed against the particular Axess Pro installation when ordering.
📦 Kit Includes
The Axess Pro Mounting Bracket Kit includes:
- 1 x Angle Mounting Plate
- 1 x Mounting Angle
The mounting plate features a 92mm x 92mm hole pattern.
The mounting angle measures approximately 50mm x 50mm x 265mm.
Key Features
- Genuine ATA Axess Pro mounting solution
- Designed for Axess Pro Series 3000 industrial operators
- Heavy-duty two-piece bracket arrangement
- Includes angle mounting plate
- Includes separate mounting angle
- 92mm x 92mm mounting plate hole pattern
- 50mm x 50mm x 265mm mounting angle
- Provides secure operator mounting
- Assists with correct drive alignment
- Suitable for chain-driven industrial roller shutter installations
- Suitable for new Axess Pro installations
- Suitable for replacement operator installations
- Designed for commercial and industrial roller shutters
Specifications
- Manufacturer: Automatic Technology Australia (ATA)
- Product: Axess Pro Mounting Bracket Kit
- Application: Industrial Roller Shutter Operator Installation
- Mounting Plate Hole Pattern: 92mm x 92mm
- Mounting Angle Size: 50mm x 50mm x 265mm
- Kit Configuration: Two Piece
- Mounting Plate: Included
- Mounting Angle: Included
- Compatibility: ATA Axess Pro Series Roller Shutter Operators
Compatibility
Designed for compatible ATA Axess Pro Series 3000 industrial roller shutter operators, including applications within the:
- Axess Pro 3100 Series
- Axess Pro 3300 Series
- Axess Pro 3110
- Other compatible Axess Pro 3000 Series configurations
ATA’s Series 3000 documentation lists the bracket kit as a key accessory across the Axess Pro range.
⚠️ Please Note
This listing is for the Axess Pro operator mounting bracket components only. The Axess Pro motor, drive chain, sprockets, control console and other accessories are not included unless specifically stated.
Some current listings state that mounting bolts are not supplied with the bracket kit. Appropriate fasteners must be selected according to the supporting structure and installation requirements.
Correct operator positioning and chain alignment are essential. Installation should be carried out by an appropriately experienced industrial door technician.
